CuteLink Product

Trust our experience to build your network

An Innovative Access Solutions & Equipments Provider

MSAP MSTP SDH,PDH Optimux Multiplexer,Fiber Modem,EOP Protocol Converter,PCM,TDM Over IP,EOC Cable Modem,GPON&EPON OLT&ONU,PTN CPE Access Devices,IP-OAM Devices

Your Location: Home >> CuteLink Products

Product Name 16E1-Eth Access Gateway Mux
Product Model CL-GW16
CL-GW16 16E1 GATEWAY is the a multi-E1 convergence-type bridge equipment, it provides 16 E1 and 4 FE interfaces, possesses Channel convergence function, according to the different bandwidth can divide into 1~16 Channel. Each Channel is composed of one or multi-E1 lines, the Channel as the link unit carries the Ethernet data transparently, and it has the function which is similar to EPON, any Channel under the user need can set up isolation or communication. Make use of the Channel as the link unit what is composed of E1 lines can realize point to point or point to multi-point flexible networking, and meet the users variety of bandwidth and centralized network management needs.

CL-GW16 16E1 GATEWAY not only provides complete alarm instructions of the line side and the Ethernet side, but also provides the error rate statistics, timeout warning, Ethernet traffic statistics management or other exhaustive management information. Network management approach respectively provide based on WEB, PC interface which based on TCP / IP, and library files which based on SNMP to build the  SNMP network management that can be unified operation and management.
CL-GW16 16E1-Eth Access Gateway Mux point to multipoint
Provide 16 E1 interfaces, and 4 FE Interfaces.
Support 1 ~ 16 Channel division configuration, each Channel is composed of 1~16 E1 that have been specified by users, the Channel as link unit point to point carrying Ethernet data transparently and independently.
Support one point to multi-point applications (Channel number is greater than 1), and point to point networking applications (Channel number is equal to 1), up to one point to 16-point networking application.
Under the point to multi-point mode, support the different manufactures single E1 Bridge and multi-E1 Bridge as the remote device mixed networking application.
When Channel is composed of one E1, it compatible with single-E1 bridge equipment that is realized by CL-EOP and CL-C  protocol converter.
When Channel is composed of two or more than two E1 lines, it compatible with multi-E1 Bridge equipment that is realized by CL-C series, and will also compatible with all Bridge device that from different manufacturers but supports the EOP protocol.
Support communication between any Channel, and can set isolation or communication according to the users need.
Each Channel supports 802.1Q Tag VLAN and QinQ function.
The Ethernet data from Channel completes frame re-sequencing technology at the E1 line side, effectively guarantees the frame sequence and improves the transmission efficiency.
The maximum transmission delay is 64ms between any two E1 lines in Channel, it can guarantee steady operation under kinds of complex networks.
Each E1 line only costs 64Kbps overhead.
The Channel automatically detects available E1 lines in it, and automatically allocates bandwidth.
The Channel supports each E1 line to set CRC error threshold in it, when one lines error rate exceeds the threshold, the system can automatically shut down the E1 line for isolation.
The Channel achieves a one-way off-isolation in it, only cuts off the E1 line that over the BER threshold, and the other direction of transmission is not affected, Ethernet data can be asymmetrically transmitted in both direction, in order to ensure the maximum data transmission efficiency when the E1 line goes wrong.
When one direction of E1 line received a LOSS or AIS alarm in Channel, the sending direction of the E1 line will not be affected, then realizes the asymmetric transmission on the E1 line.
When receiving direction of all the E1 lines are cut off in Channel at the same time, local alarm and network management information can still be transmitted to remote via sending direction, achieves a one-way transmission on E1 line. This feature is particularly suitable for protocol converter cooperates with optical communication equipment. It can judge the faults of the lines when the optical communication equipment appears a one-way fiber cases.

Support loop-back and loop-back protection of each E1 line.
Support Ethernet packets statistics function.
Support local system to control each remote E1 loop-back.
Support the transfer function of full fault alarm.
Support BERT testing function of E1 line.
Support remote alarm indication.
Support particular Ethernet packet statistics function.
Support WEB network management features, support network interface of the PC which based on TCP / IP, open SNMP library files, support the customer to complete network management that based on SNMP.
Protocol:  G.703, G.704, G.736, G.823, I.431 IEEE802.3
Bit rate
Code format
75 Ohm is default, Optional 120 Ohm
Jitter transfer, Jitter tolerance comply with ITU-T G.703G.704G.823 recommendations
Electrical Ethernet Interface
Working mode
Auto - negotiation is the default setting
Complies with IEEE 802.3 and 10/100 Base-Tx Ethernet Protocol
Ethernet parameters
MAC address table capacity
MAC aging time
five minutes
Minimum frame-length
64 bytes
Maximum frame-length
1916 bytes
Working mode
Support auto-negotiation compliant to IEEE802.3u.
Enabled as default
Configured via Web network management
VLAN function
Disabled as default
Flow control
Enabled as default
Default is 16E1 31.68Mbps
E1 interface
Bit rate
Code format
75 Ohm is default, Optional 120 Ohm
Jitter transfer, Jitter tolerance comply with ITU-T G.703G.704G.823 recommendations
Dimension, weight and power consumption
434mm44mm155mmwidth height depth
3.5 kg
Power consumption
Environmental requirements
Operating temperature
Storage temperature
95free from condensing


                                   CL-GW16 NMS main interface
CL-GW16 16E1-Eth Access Gateway Mux nms
         CL-GW16 NMS E1 Channel E1 Group configuration


Order Info.:
4Eth support Vlan,16E1 uplink  can work with CL-EOP and CL-C converter,support Web SNMP NMS
Compatible With Cutelink CL-C and CL-EOP Protocol Converter
10/100M Base-T to E1, 75/120ohm, (N*64K)framed/(2M)UnFramed,Support Vlan,AC220V or DC-48V
      CL-C4200 4*10/100MBase-T to 4E1, 75/120ohm, framed,AC220V+DC-48V(4 Ethernet ports,4E1 Ports)
     CL-C8400 4*10/100M to 8E1, 75/120ohm, framed,AC220V+DC-48V(4 Ethernet ports,8E1 Ports)
CL-EOP4/8/16 CL-EOP4/8/16, Ethernet to 4/8/16E1 converter with components of EOP4 /8/16motherboard +4/8 E1 card +4Ethernet port LAN cards